HOW TO INSTALL A BATH TUB

How to Install a Bath Tub

How to Install a Bath Tub

Blog Article

Book Your Appointment

The content down below relating to Tools You Need to Install a New Bathtub is amazingly remarkable. Don't miss out on it.


How to Install a Bathtub Yourself
Mounting a bathtub isn't precisely brain surgery, yet it does require strong plumbing, woodworking, and also in some cases, tiling abilities. Replacing an old bathtub with a brand-new one is also a reasonably hard project. If the old tub is conveniently accessible, the job can relocate easily; if you have to open a wall surface to get rid of the old tub and position the brand-new bath tub, the task is much harder. In either situation, the job is within a residence handyman's skills, although you will require an assistant to vacate the old tub and set in the brand-new one. See to it you have actually qualified yourself for the job as well as fit trying it. As opposed to working with a professional to take over a halfway-completed project, it is much better to think about utilizing one prior to you start. Opportunities are you might require a specialist plumber to make tube connections.
This write-up will certainly aid you mount a brand-new bathtub in your bathroom if you have already bought a new tub and don't need to change the arrangement of your previous water supply pipelines.
Your devices and also product list need to consist of the following:
  • New Bath tub

  • Hammer

  • Pipeline Wrenches

  • Prybar

  • Shatterproof glass

  • Degree

  • Pliers

  • Flexible Wrench

  • Putty Blade

  • Screwdriver

  • Cold Blade

  • Tape Measure

  • Pipe Caps


  • Removing Old Taps


    If you need to replace old taps with brand-new ones as a part of your installment, after that the first thing you must do is separate the water system. After doing so, switch on the taps to drain any water remaining in the system. The procedure of getting rid of the existing faucets can be rather troublesome due to the restricted access that is usually the instance.
    Utilize a basin wrench (crowsfoot spanner) or a tap tool to reverse the nut that attaches the supply pipes to the taps. Have a cloth all set for the continuing to be water that will certainly come from the pipes. As soon as the supply pipelines have been removed, make use of the very same tool to loosen the nut that holds the faucets onto the bath/basin. You will certainly need to stop the solitary faucets from turning throughout this procedure. When the taps have actually been eliminated, the holes in the bath/basin will need to be cleansed of any type of old sealing substance.
    Before moving on to fit the brand-new faucets, compare the pipeline connections on the old taps to the brand-new taps. If the old taps are longer than the brand-new taps, after that a shank adapter is needed for the new faucets to fit.

    Fitting New Taps


    If the tails of the brand-new taps are plastic, after that you will need a plastic adapter to avoid damage to the string. One end of the connector fits on the plastic tail of the faucet and the other end provides a link to the existent supply pipelines.
    If you need to fit a monobloc, then you will certainly require lowering couplers, which links the 10mm pipe of the monobloc to the typical 15mm supply pipe.
    Next, place the tap in the placing hole in the bath/basin making certain that the washing machines remain in area in between the tap and also the sink. Protect the faucet in place with the supplier offered backnut. As soon as the tap is firmly in place, the supply pipelines can be connected to the tails of the faucets. The taps can either be linked by utilizing corrugated copper piping or with normal faucet adapters. The former kind should be linked to the tap ends initially, tightening only by hand. The supply pipelines can later be attached to the other end. Tighten both ends with a spanner after both ends have actually been attached.

    Setting up the Tub


    Using the two wood boards under its feet, place the tub in the called for position. The wood boards are handy in evenly spreading the weight of the tub over the location of the boards instead of concentrating all the weight onto 4 small points.
    The following goal is to guarantee that the bath tub is leveled all round. This can be achieved by inspecting the level and also adjusting the feet on the bathtub until the spirit level reviews degree.
    To install taps, fit all-time low of the outermost flexible tap adapter to the ideal supply pipe by making a compression join; then do the same for the other tap.
    Activate the water supply and check all joints as well as brand-new pipework for leakages and also tighten them if necessary. Fill up the tub as well as additionally check the overflow electrical outlet and the normal outlet for leakages.
    Ultimately, deal with the bath paneling as described in the manufacturer's instruction manual. Tiling as well as securing around the tub must wait till the tub has actually been made use of at the very least when as this will certainly resolve it into its final position.

    Preparing for the Setup


    Firstly, the supporting framework supplied with the bath must be fitted (if needed) according to the maker's directions. Next off, fit the faucets or mixer to the tub. When suitable the faucet block, it is very important to see to it that if the faucet features a plastic washing machine, it is fitted in between the bathroom as well as the faucets. On a plastic bath, it is likewise practical to fit a supporting plate under the taps unit to stop pressure on the bath tub.
    Fit the adaptable faucet ports to the bottom of the two taps making use of 2 nuts and also olives (occasionally provided with the bathtub). Fit the plug-hole outlet by smearing mastic filler round the sink outlet hole, and afterwards pass the electrical outlet via the hole in the bath. Use the nut supplied by the supplier to fit the plug-hole. Take a look at the plug-hole electrical outlet for an inlet on the side for the overflow pipeline.
    Next off, fit the end of the flexible overflow pipe to the overflow electrical outlet. Afterwards, screw the pipe to the overflow face which should be fitted inside the bathroom. Make certain you utilize all of the provided washing machines.
    Link the trap to the bottom of the waste outlet on the bath tub by winding the string of the waste outlet with silicone mastic or PTFE tape, and also screw on the catch to the outlet. Attach all-time low of the overflow tube in a similar manner.The bath need to currently be ready to be fitted in its last setting.

    Tiling Around the Bathtub


    In the location where the bath meets the floor tile, it is needed to seal the accompanies a silicone rubber caulking. This is very important as the fitting can relocate enough to crack an inflexible seal, triggering the water to penetrate the wall surface between the bathroom as well as the tiling, leading to issues with moisture and feasible leaks to the ceiling listed below.
    You can select from a variety of coloured sealers to assimilate your fixtures and also installations. They are sold in tubes as well as cartridges, and can sealing voids as much as a size of 3mm (1/8 inch). If you have a larger void to fill, you can load it with twists of drenched paper or soft rope. Remember to always load the tub with water prior to sealing, to permit the motion experienced when the bathtub is in usage. The sealant can split fairly early if you do not take into account this motion before sealing.
    Conversely, ceramic coving or quadrant tiles can be utilized to border the bath or shower tray. Plastic strips of coving, which are easy to use and also cut to size, are additionally easily offered on the marketplace. It is recommended to fit the ceramic tiles making use of water-resistant or water-proof adhesive as well as cement.

    A Step-by-Step Guide to Installing a Bathtub


    Is your bathtub looking a bit dated lately? Believe it or not, installing a new one is a project you can do yourself. Whether your bathtub is broken or doesn’t fit in with your current bathroom’s design, you can fix it without having to hire a contractor or paying labour costs.



    But, beyond saving money, there are other benefits of installing your own bathtub. When you do this project yourself, you can customise every step of the process. You can also make sure the finished product looks exactly the way you want it to.



    This DIY project is quite involved, but by doing some research, preparing your bathroom and using the right equipment, it is definitely one you can take on. This guide will help you understand the technical procedures behind installing a new bathtub.


    Remove the Existing Bathtub


    To remove the old bathtub, you will need to turn the water supply off before you start any work. After you turn the water off, there will likely still be some water left in your plumbing system, which you can remove by turning on a faucet below the level of the bathtub. Once the water stops running, you are ready to start working.



    The easiest way to remove the tub is to remove the faucet, handles and other piping and then pull the tub out from the wall. If this doesn’t work in your situation, you will need to remove part of the wall, remove the piping and then slide the tub out.


    Choose the Right Bathtub


    The ideal way to replace your bathtub is to find one that has the exact dimensions and has the drain and faucet on the same side as your old one. This way, it will fit in the same place and you won’t have to change the piping system in your bathroom. Choose a tub that matches your home’s decor and fits with the style of the bathroom.


    Install the Plumbing and Ledger Board


    You can purchase a tub drain kit at a hardware store which will have all the pieces you will need for your new tub’s plumbing. Follow the instructions that came with the kit to install the plumbing in the new tub and then take measurements to make sure the plumbing in the tub will align with the plumbing in your bathroom. If it doesn’t, now is the time to make necessary adjustments.



    Some bathtubs need a ledger board that is installed on the wall behind the tub to help support it. If your new bathtub requires one, the directions that came with it will tell you how high it should be installed. If your old bathtub had a ledger board, and it is still in good condition, you can adjust its height to match the new bathtub.


    Install the Bathtub


    When the plumbing and ledger board are ready, you can install the new bathtub. Carefully lower it into the space, being careful not to damage the tub, wall, plumbing or ledger board. Since bathtubs are very heavy and you will need to line the tub up exactly, it is wise to have someone help you with this step.



    Once the tub is in place, it needs to be perfectly level, so use a bubble level instead of estimating how level the tub is. Put the level on the top edge of the tub, not the bottom on the inside, since many tubs are designed with a sloped bottom.



    If the bathtub isn’t level, adjust the ledger board and shift the tub until it is. When it is level, use screws to attach the tub to the wall studs. Most bathtubs have pre-drilled holes in the upper flange, so use these but do not over tighten the screws.


    Hook up the Plumbing


    Now that the bathtub is installed, it needs to be attached to your plumbing system. First, install the shoe fitting under the tub and drain pipe, then the overflow pipe and then the drain flange. Your tub plumbing kit will include specific instructions on how to install these pieces.


    Install the Bathtub Surround


    A bathtub surround will protect the walls around the tub from water damage and can give your new bathtub a more finished look. To install one, make sure the wall is completely clean and dry so that the adhesive will be able to hold the surround securely. Then, measure the surround and mark the same dimensions on the wall above the tub.



    Following the directions that came with the surround adhesive, apply it to the wall. Press the surround against the wall on top of the adhesive and then pull it away for about three minutes to activate the adhesive, then apply the surround again. Keep in mind that this is the most common way to use an adhesive, but you should check the instructions on the package for any special steps.



    If there is any excessive adhesive around the sides of the surround, you can use mineral spirits to remove it. Then use masking tape to hold the surround panels in place until the adhesive is dry. Using silicone, seal all the cracks between the surround panels and the gap between the bottom of the panels and the top of the bathtub.



    If you want to install tile above your bathtub, instead of a bathtub surround, the process will be very similar. But, you will need to measure and cut tiles and install each one individually, using tile spacers to make sure they are evenly spaced. You will then use grout to fill in the spaces between the tiles.

    https://www.hss.com/blog/bathroom/a-step-by-step-guide-to-installing-a-bathtub/


    How to Install a Bathtub Yourself

    We hope you liked our article about Tools You Need to Install a New Bathtub . Thanks a lot for spending some time to read our posting. Loved our review? Please share it. Let others locate it. I take joy in reading our article about How to Install a Bathtub.



    This Post

    Report this page